Largest version design, smoke "dark". 13 1/2 inches deep, 5 inches high, 19 inches wide. Center point of hinges 12 inch space. 8+/10 condition, minor light hairline scratches, but was buffed. Plastic is still very nice.
Spindle assembly mounted on PCB. Motor #TPM-5A. #9 condition.
Standard headshell for "vintage turntables", black with silver trim, fingerlift Sony logo, hardware + original box, bayonette, neck nice condition, #9+
4322 010 02043 / 117V 300RPM 60Hz Football shaped mounting plate with 2 holes. With 2 stage pulley that takes square belt. Has finger on pulley to shift belt. Goes into older version Philips - NOT GA 212 or 312 units. Send us a picture of your motor. Condition #9+
used good condition, with IC#8340630 Pulled from turntable w/ broken arm. Condition #9. (2) Available Priced Each
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Circuit board, MCB-1 Rev 1, control triac, may need new caps - we can do here, colored wire leads on board, condition #8+
Drive mechanism motor with worm drive, circuit board, arm string and wiring harness to main board complete, needs drive belt, value is mostly for motor, known workings, #9
Used in ATP-2, replaces ATP-N2. 78rpm. New stock.
Excellent condition, tested, came from low use table.
For Dual 1209, 1219, and 1229. Headshell with wires. Newer version with slim design. Condition: 9
United Audio logo badge. Walnut veneer base w/ press board bottom. (16 10/16" W X 14 6/16" D X 3 1/2" H) Has slot (Full length) on rear for dust cover. 16" long 1/4" wide. Good condition left front foot broken (easy repair) few H2O stains on front left bottom edge w/ chip. Can easily be refinished. Chip i svery minor 1/2" chip. #8 condition.
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
motor, #18-008-05, 24 pole, 300 RPM, with aluminum pulley jumper clips, condition #9
Motor: 214 837. With three speed pulley. Cleaned, flushed and lubricated for long term reliability. #8+
Motor: no number. With 4 speed pulley. Cleaned & lubricated. 16RPM pulley has minor crack at top. Tested, low use. #8+
TPM-2C Motor, with BA6303 special IC #9 condition
Part: 632029 Board#. DDM-518F. Field coil OK. Selling motor board only (No Rotor magnet). Motor collapsed, needs repair. Board still good. Condition 8
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
With auto cycle gear. Used, tested, excellent.
SS09BA 100143. With wire harness and switch. Excellent condition.
MMI-6S2RwH Turntable motor DC12V. With 4 wires, fits many models. With brass belt pulley. Salvaged from a working unit, tested. #9+ Condition.
Board #TK-MF194-0. Excellent condition.
P1021B501A,2A,3A,4A,5A. Excellent #9 condition.
We are presently operating on an APPOINTMENT ONLY basis. Please call us first at (617) 926-8020 to schedule an appointment before you come into the shop for repairs, rentals, product recommendations, consultations, or anything other than minor purchases.
12 VDC Motor with brass pulley & regulator IC. #9 condition
Master control board. Fully intact. All switches. Board #X25-2940-00, J25-4988-31. Tested. Low use. #9 condition.
