Complete motor with spring, pitch adjust assembly, pulley, and original wire harness. C-clip mounting; does NOT have original hardware. Salvage from a low use machine. Tested and oiled, with rebuilt pitch adjust mechanism. Condition: 9
(Matsushita) DC3V, tested good, With brass pulley + wiring harness w/plug USED in Model type 5712 5773 Pulled from salvage units. #9 good condition.(2) available, priced each.
mounted in frame [3 3/8" x 2 7/8"] with four mounting stands on top. Excellent condition. Missing the top nut which holds the pitch gear adjuster, but it can easily be taken from your existing motor and put on this one. 9/10 condition. Clean before shipping. Unit has red coverings on coils.
Direct drive motor with board, spindle, and axle gear. Excellent condition, tested.
(2 available), #8 condition, salvaged and tested
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
#1-587-955-1 , transformer #1-446-079-11 IKVY, salvaged from working machine, sensor switch, pitch control, strobe, all intact, #9 condition, salvaged
Motor and board. EDS 910 934 5810 001. Has original brass pulley and black plastic gear. Tested, good, low use. 9 condition.
MMI-6S2RWH with transformer, board #OP781T4. 9/10 condition, from a low use machine.
w/ power switch, pitch control + speed reg boards, part # 180 S1 08510010, reg board # 4-2262-18130, pitch control board # 18150A, power switch board # 18160, condition # 9, salvaged from working unit
Speed Shift Lever - 1 unit available Please Read Carefully! This is the rarest demanded lever Total 2 and 1/2 " long - threaded end is 1/4". Lever itself has 2 cuts to allow fit into speed pitch dial. Paddle is 1 and 1/2 inch long and paddle width is 1/2". 1 available with slight wear #8 condition
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
EG-530SD-3F, 5/12 vDC, 1130/1520/2360/1405 RPM, regulator on board, wire harness w/ switches (bushings+mount screws) , often substitutes for many of these motors, tested condition 9.
(1) Available. 9V, 12V CW motor. With plastic pulley. Like new. Condition 9.
Older original version pitch control. Retrofit to mount plate, complete assembly on board SFDP112-13. With cable. New.
-comes with elevator gear for pitch control
-black and white
-with brass motor pulley
- comes with complete grommet and washer clip kit (QC'd / oiled motor bearings 1.28.21) Condition #9
CD Transport. Goes into an SLP7. Semipro CD assembly. Goes into Semipro consumer machines. Board houses IC's: 1. AN8377N Technics IN. 9, 2. 83745 ID.S. Tested, low use, spindle table rubber slightly aged but acceptable. Condition #9
Check us out on facebook.
#SFDPC02N02, tested, known low use, #8+
Direct drive turntable motor in black cup assembly with board, spindle axle, and lead wires.
no spindle, but with magnet rotor plate. Excellent condition.
Equivalent MMN-6C2LKC. With motor board, transformer, and switch. Speed switch. Tested and cleaned. Condition 8+, salvaged from low-use machine.
Complete motor and board. Excellent #9 condition, tested and cleaned, low use time.
This is equivalent to: IM-S275-12BUC and M712L-10530V. Syncronis AC 120 volt. 3 Inch square, 1 1/4 high with brass pulley. 4 screw holes to mount into units. #9 condition. Low use.
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Micro Controller board. 83962 720 00/273.701 550023.00.000. Has push controls, salvaged from working unit. 9 condition.
Motor and Board PXM-090-D. With PA 2007 and PA 2008, special motor IC. 9/10 condition, completely tested.