Wand/Tonearm "pipe." For Thorens TD110, 115 (and others). Includes: Cartridge mount hardware, alignment gauge, mirror. Like new - not used. Missing original outer carton. Condition 9+.
(1) Available. 9V, 12V CW motor. With plastic pulley. Like new. Condition 9.
Ion turntable preamp USB board. Board salvaged from unit with all cables and wires. Condition 9.
Ion USB Board. PC05P002A. Preamp board with USB circuitry mounted on frame. Condition 9.
Counterweight substitute. Looks very similar. Condition #9.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
9.9 Shaft, 81 Grams counterweight, condition #9
EG-530SD-3F, 5/12 vDC, 1130/1520/2360/1405 RPM, regulator on board, wire harness w/ switches (bushings+mount screws) , often substitutes for many of these motors, tested condition 9.
4 Speed, 60Hz Brass pulley For use on 5mm axel Pulley shows some wear but good - condition #8
Use for a single 33 play record. This spindle is a short spindle with rubber stop collar. Custom made with spacer grommet. Works like original. Fits BIC 920,940,960,980 1000 models 3 Available Excellent condition #9+ condition - $12/ea
Dust cover with hinges complete. Cover does have some scuffs, maybe able to buff off. Good condition no cracks or broken corners. Value mostly for the hinges. #7 condition
Contact us about similar items or replacement parts.
We have been selling and repairing professional and consumer audio equipment for over 40 years. (Read some of our customers testimonials here).
used good condition, with IC#8340630 Pulled from turntable w/ broken arm. Condition #9. (2) Available Priced Each
Turntable motor with pulley, mount plate & wiring harness. 12 Volt. Serviced from turntable w/ broken tone arm. Good Condition #9
Contact us about similar items or replacement parts.
Parts available Motor, Platter, Platter matte, Counter Weight, Main Belt, Dust Cover. NOTE: No headshell carrier, No pitch belt.
(5) available, priced individually. Machined aluminum. Heavy weight. Shows some wear. Condition #8
United Audio logo badge. Walnut veneer base w/ press board bottom. (16 10/16" W X 14 6/16" D X 3 1/2" H) Has slot (Full length) on rear for dust cover. 16" long 1/4" wide. Good condition left front foot broken (easy repair) few H2O stains on front left bottom edge w/ chip. Can easily be refinished. Chip i svery minor 1/2" chip. #8 condition.
Speed selector mechanism for 33/45 . Includes steel rod and cage to guide lever as well as the screw . Also has the start stop switch. No tear drop handle included (check our other listings) Good condition #9 pulled from a damaged unit
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Type (#5773) Many parts available. Unit in good working condition. Dust cover (SOLD) Counter Weight ($14) Platter ($20) Motor ($60) Cartridge MMC-4 (Call) Cartridge suspension is bottomed out. Belt removed. #8 + good condition. Dust cover is excellent!
Bang & Olufsen counter weight for RX -series. ( 1 and 17/16" l x 10/16 Dia , center shaft hole 3/16" ). Arm shaft still attached to counter weight but broken at attachment point - For replacing Counter Weight Only . Used - pulled from damaged unit. #9 Condition.
#431 10132, Possible 3V - 9V DC Motor, For Use on Turntables (Technics), Clockwise Motor, Needs Outboard Regulator, With Plastic Pulley, Tested OK, Condition #9
Parts unit - Call for Price and parts. Available parts include : Dust cover - no cracks but typical swirls and scratches and can be polished out #7 condition. Platter Matte, Platter, Motor, Counter weight # 9 condition No Headshell. Please call for price and availability.
Speed Shift Lever - 1 unit available Please Read Carefully! This is the rarest demanded lever Total 2 and 1/2 " long - threaded end is 1/4". Lever itself has 2 cuts to allow fit into speed pitch dial. Paddle is 1 and 1/2 inch long and paddle width is 1/2". 1 available with slight wear #8 condition
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Matsushita MMN-6P2RK 8 VDC motor with brass pulley , mounted on circuit board # SUP 15700A / TP-N88S from low use working unit #9 condition.
(1) MMI-6S2PRI with pulley ($28) (1) Motor for Linear arm with pulley ($24) Low use tested & clean #9 condition