For tensioner system, No arm, but all other related parts behind the arm, 3 springs, dampener cylinder, washers, complete assembly's for left & right sides, It's a complete kit of parts, $24 each. (2) available. Left/right string can be changed over to make either side operate.
(Arm #1) Back tension arm only with nut, obvious wear on arm, has black finish tip for Tape guide (screw on) #9 Condition $36--------(Arm # 2) Old version, all metal, has minor stains, arm only no nuts to mount, #8 Condition $20 For models 2300, 2300 SD, 3300 series & 3400.
$280, Tascam 388 erase head 53783061 $160 heads have connectors (presently mounted on head block) condition #9+ no visible wear path
Contact us about similar items or replacement parts.
Fits better w/ GX Series, but not certain. 17" wide 17&10/16" High 2&1/8" deep. Akai logo in white lettering upper right hand corner. Soft plexiglass type cover w/ hinges (clip on type) on left side. right side broken. good condition, no major scuffs, but some small scratches; cover could be buffed. Read dimensions carefully. Condition 8-
(1) Set off head bracket holders Frames screw 3 holders, no reel tables, no pinch rollers, no heads, no screws
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
10 Inch Reel Table. Also for 3340S and 3300S. Nice Metal Finish. Very clean. Very minor fracture at stem base does not affect use.
Contact us about similar items or replacement parts.
100KA ohm, (Uses red knob-not included) Best quality fader, this is a replacement fader which matches install screws. has longer stem, original knob will not fit as is, but stem can be cut down to fit. Condition #10 (3) available
53783019 2 Track. Heads are 75% good or better. Could be lapped to 95%. Has good wear path. All heads are mounted pm original plate. Similar heads with similar wear perform near perfect with minor calibration. Price is for all 3 heads. Call 617-926-8020 for individual pricing.
Contact us about similar items or replacement parts.
PP30-4202 70% good. Must use fresh head pads and re-calibrate Rec/Play levels. Head mounting hardware. Condition 7. (2 Available) $38/ea
Complete transport controls with all buttons knobs and wires. All switches and pots have been cleaned. Some wear on lettering. Worn looking but known to work. #7 Condition.
FYI, Around the database you will often see us describe the condition of units on a scale of 1-10. #10 would mean the product is new from one of our suppliers, such as Behringer, Audio Technica, etc. #9 means the product is in perfect condition but is used, #8 implies there are some minor cosmetic scratches but unit is mechanically perfect, and so on and so forth.
A complete back plate with all connectors and corresponding PCBs. Connectors appear good but has seen use over time. Heat sink power supply regulator board (with 6 transistors) can be sold separately - $40. #8 condition.
Inner transport face plate that is located under the reels. #8 condition.
10KA (8) available with connectors, white fader knob (not included) , can fit, but will sit higher $14. (2) 20k ohm A better version control $18, Refer to 71277.
2 Available. Program master fader. 10KAX4. uses orange knob-cap , (4 channel buss fader) #8 Condition , also (2) 10KA version 4 buss fader but shorter design is 3 inch long - it will fit and operate the same #10 new.
2 Available Bracket and PCB included. Meter 5296006600. Meter PCB 52101116-00, TP-S47-T. Bulbs Good! #9 Condition.
Buss Board 1 to 8 Part # 52101748 #9 Condition.
We offer expert time-saving advice on repairing many types of home and studio equipment, as well as consulting for product and recording issues, at a fair and reasonable cost. For complex matters, we sometimes must charge a small technical fee. If we can help solve your repair problem or technical conundrum, give us a call. (617)926-8020.
NM01 Micro motor. #9 Condition. (Vince personal part)
Buss PCB Part # 52101734-02 #9 Condition.
1 Reel Table #9 Condition - SOLD. 1- Left side brake band assembly $24, 1 Take Up Flutter Roller 1 1/4" - $32. 1 CAP 1 1/4" - $14. 2 Flutter Roller Tension Arm Assembly L/R - $28/ea. 2 Reel Motors #9 Condition - $88/ea. 1 Pinch Roller #9 Condition - $24. 1 Pinch Roller Cap #9 Condition - $22. Call to check on any other parts not listed.
1 Reel Motors $64. 1 Flutter Roller 1 1/4 Inch Diameter $28. 1 Flutter Roller Cap Black 1 1/4 Inch $22. 2 Balance tape guide flutter roller $42/ea. 2 flutter roller cap 3/4 inch diameter $22/ea. Everything is #9 Condition.
Buss Board B Part # 52101736-02. #8 Condition. Test Good
Somewhat dented and nicked but intact. TLC needed. People can put new veneer on sides, obvious dent in one corner on the front and veneer peeling on the back, but still a good deal for side boards! Price reflects condition, perfect board could be about $40-$50 #7 Condition.
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
15" Long. 2" Wide. Worn looking but totally functional. Spray paint refinish is possible. #7 Condition.
More of this part may be available, cost can be over $100 Call for more info 617-926-8020