Dual meter with special design. 2 available. Tested and working, in excellent #9 condition. $22 each.
Contact us about similar items or replacement parts.
Faceplate 9/10 condition (one dent) - $14. Dust Cover with hinges 8/10 condition (minor scuffs) - $14.
Pinch roller 9/10 condition $16. Drive Idler 9/10 condition $16. Head 8+/10 condition $16.
Parts machine, CrO2/CH/Fe-Cr/metal tape selector. Dolby B-C noise reduction. Remote punch-in control. 3 head automatic demagnetizing system. Silver face, tape counter. Rec/play, auto-rewind, mic inputs, tape monitoring. Tape counter belt replaced, cleaned/calibrated, low use hours, 8+ condition.
Local customers, please do not come to the shop without calling ahead first - (617) 926-8020 - for an appointment, so that we can more efficiently help you with your equipment or sound recording needs.
Could be "5R2" or "5B2." Pulley included. Salvaged from low use machine.
100KAX2. With knob. 9/10 condition (like new).
motor XMI-6B2HW, CCW motor, 2 available, w/white removable pulley, tested, low use, condition #9
2.75" square. Excellent condition.
7/8" diameter, rubber tire on base, excellent condition. Four pieces available.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
for ff/rewind, one black, three silver. Excellent condition.
about 2" diameter, shaft length .5". Very good condition, three pieces available.
Six knobs. (1) 7/8" diameter, (2) 11/16" diameter, (3) 3/8" square. Excellent condition.
7/8" diameter. Very good condition, two pieces available.
1.5" diameter, felt pad and nylon wheel. Very good condition, five pieces available.
Cassette deck. Pinch roller good. Better version unit. Hinged dust cover added. Nicely done by customer. Walnut veneer base. (FF/REW) works. No service. 80% good heads. Excellent cosmetics. Rubber bad! New rubber belt kit needed. Condition 7
We are presently operating on an APPOINTMENT ONLY basis. Please call us first at (617) 926-8020 to schedule an appointment before you come into the shop for repairs, rentals, product recommendations, consultations, or anything other than minor purchases.
Vintage cassette deck,, Single large VU meter. CrO2/Reg(normal) tape switch. Dolby B noise Red No/Off (first Cassette Deck to use!) and Stereo/mono switch. Note: Missing Pinch rollers +arm (sold) unit can be used for many parts or restored. Nice plexi cover, has chip under right corner. Used, #9 good condition.
Head cycling gear cracked. Otherwise good for motor, pinch rollers, idler, tape head. No belts. Low use head worn 80% good. 8
Transport Motor MMA-6B2LWFC. Head cycling gear cracked. Good for motor, pinch rollers, idler, tape head, gears. No belt. Low use, 90% good head, #9 condition
Contact us about similar items or replacement parts.
Motor with brass pulley. Salvage. Test good. Condition #9.
Part # MM1-652LK, tested and working, has been oiled, #9 condition.
Contact us about similar items or replacement parts.
Check us out on facebook.
Part # MM1-6A2LKPA, oiled, tested and working. Condition: 9
Contact us about similar items or replacement parts.