Cassette transport with connectors intact. With MM16H2LWC1 1 direction transport. Tested, works, fully functional. #9 condition.
Motor. DC6V. With brass pulley. Salvaged. Condition #9.
Plastic pulley with small PCB for connections, colored leads included. Low use. #9 (2 available)
(4) Available, MMI-6H2LWK. DC 12V w/ printed circuit film type connector. With nylon pulleys. Good condition. #9 condition.
MMI-6A5HKSA. DC 15V. With brass "dual type" pulley. 2 wire leads, red and blue 6". Used - pulled from salvage unit. Condition #9.
We know you have many options for purchasing audio equipment and parts, and we truly appreciate your business. We strive to offer good products at competitive prices. While we can't always match the prices of one isolated reseller, we make up for it by carefully selecting, testing, and finding unique and special rare parts, and we are here for the long run. We guarantee everything we sell and we hope it helps you to enjoy a great listening experience.
MMU-5B2LWAI. DC 12V. No pulley - shaft length = 0.375" = 9.5mm. 2 available. Used good condition. #9 condition.
FF/RR motors for Sony WR series. Excellent condition. 3 Motors available - (1 labeled ZB3 226, 1 labeled ZB3 066, 1 labeled ZB5 227, All have nylon pulley at base of shaft 1 motor has the planetary arms and spring) All motors have 3 wire plug in cable attached Used Excellent condition #9
w/ motor board. 3 wire motor. Condition #9.
12 VDC motor CCW. With brass pulley. Tests good. Condition 9.
Motor with brass pulley. 12V CW. Tested good. Condition 9.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
(4) available, priced individually. DC 12V motor. With printed circuit film type connector. With nylon pulleys. Condition #9.
(2) Available. Lubricated & tested. (Note: Can use as substitute in Nakamichi BX-series mode Commutator motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws & Washers to mount & current limiting resistor. Reuse worm gear from Nakamichi unit.) Condition #9
(Note: Can use as substitute in Nakamichi BX-series mode counter motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws + Washers to mount & current limiting resistor. #9 condition. Tested. Oiled.
Rubber Idler needs replacing. #9 condition.
Used in JVC and others. With removable nylon pulley, mounting screws, and board "JVCR73HB." (Note: Can use as substitute in Nakamichi BX-series mode counter motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws + Washers to mount & current limiting resistor. Reuse worm gear from Nakamichi unit.) Oiled and tested #9 condition.
FYI, Around the database you will often see us describe the condition of units on a scale of 1-10. #10 would mean the product is new from one of our suppliers, such as Behringer, Audio Technica, etc. #9 means the product is in perfect condition but is used, #8 implies there are some minor cosmetic scratches but unit is mechanically perfect, and so on and so forth.
Pinch roller and arm in original plastic bag. NOS Condition #10
MXN-13FB12F . (Note: Can use as substitute in Nakamichi BX-series mode counter motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws + Washers to mount & current limiting resistor. #8 condition. Tested. Oiled.
with black plastic pulleys. (Note: Can use as substitute in Nakamichi BX-series mode counter motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws & Washers to mount & current limiting resistor. Reuse worm gear from Nakamichi unit.) Salvaged from working unit, Tested. Condition 9.
includes 1" length plastic pulley. Excellent condition. (Note: Can use as substitute in Nakamichi BX-series mode counter motor - equivalent to Nakamichi VA700B04. Must drill out holes on mounting plate slightly larger. We supply 2 screws to mount & current limiting resistor. Reuse worm gear from Nakamichi unit.) Oiled & tested, Condition #9
pinch roller and pinch arm assembly for DAT machine. Used only in stock. Nice condition . Be aware of Panasonic 3700 3800 problem where tape slips out of pinch roller when rewind scan of tape is engaged. It is usually due to spring tension of the pinch roller is weak. The spring is located at the bottom arm end and is difficult to install.
complete tape transport only (deck A), includes cassette well cover, 2 motor transport, auto reverse, used - pulled from working unit, condition #9
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.