Module C-1. 2" high. Tube socket 11 pins out. For compressor. May need capacitors replaced. Looks intact inside cannot be certain of operation. #8 condition
Fuse holder for DC Stereo Power Amplifier. Original fuse holder with original washer and nut. Great condition, completely in tact. #9+ Condition.
Recording Amplifier #1077 705. Missing two trimmers, salvage from previous board, good condition, might need cap change out, #8 condition.
Unit is intact. No obvious failures in amplifier except DC to DC. Converter appears failed. Good Unit to build 1 out of 2. Condition #7
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
(2) Interior rotary switches $12. (1) power switch, probably for 700B $14. Please send pictures of your unit/parts to ensure a proper match!! 8+/10 condition, knob controls have typical slight oxidation.
Volume control. 8 legs like original. 200K value will fit with 50K 100K or 250K use. 9+/10 condition (N.O.S unused).
Parts for repair. 380004400 rev 8. AMP board only, intact low use and tested with switch. Output transistors listed 2SD746A, 2SB608A $28 each. 2 pieces or more to purchase 22 each.
For Biamp 2500, Max Surge 125VDC. 8/10 condition (known modestly used parts).
Rack Handles. 7+/10 condition. Obvious but minor scratches.
(3) Glass Bezel covers for Phase Linear VU Meters. Include a picture of your meter so we can match the cover to you!. 9/10 Very good condition.
Need your guitar or bass amp tuned up? We are now doing repairs, upgrades, and modifications to all types of guitar amps. Orange, Mesa Boogie, Fender, Marshall, Hughes and Kettner, Peavey, Ampeg, Gibson, Silvertone, etc. Read more about it here
420-04365 VU Meter. 8+/10 condition (minor wear on face).
8 OHM meter. 170 W Rated. 4 1/2 inch x 4 inch. 8-/10 condition (Was N.O.S but has 1/4in scratch in glass face below meter number area.
55 OHM. For Phase Linear 700B amp. 4 1/2 x 4 inch silver face. 8+/10 condition (very minor unnoticed scuff. Tested and used).
AMP boards F-1358, 2 channel module, Repaired tested bias set, 2 available $68. Other boards, controls, knobs ect. available, CALL. Case cover scratching on side #7 $20.
Unit requires major rework. Needs many capacitor replacements and an upgraded board regulator. Most important transistors OK. Face, mechanics OK. Worth transformers and output transitors. Needs service. 7 condition.
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
5 inch by 4 inch, meters have obvious light scratches, windows could be exchanged. #7+ $32 each.
For cosmetic use, very minor unnoticeable finger wear, old version silver scale, #7
VU Meter, clean face. #8
Contact us about similar items or replacement parts.
Complete board with cut wire lead. Condition: 9
Contact us about similar items or replacement parts.
Balance control 200k ohm. Substitute for balance control, High quality ALPS. Detented, click increments. Cleaned, lubed, exercised. Requires new holes drilled. Easy to mount. #10 Condition (New).
Low speed, virtually silent dual cooling fan. Nice slim rack package. Condition: 9
If you are having trouble finding parts, enter the name into our search bar at the top of the page. Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Main PCB assembly. Controls, switches, jacks. Silver and blackface faceplates. Available for various parts. Call (617)926-8020 for availability of specific parts.
Bad solder joints and corrosion inside of machine. Right channel has failure - possible predriver. Low level caps need to be replaced. Fuse holders unsecured. Most mosfets good. Cosmetically OK, minor scratches/corrosion. Unit sold as is for parts. Call (617)926-8020.