Counter weight . Black with silver numbers and scale. Very good condition #9
Unit is functional but cartridge mmc-5 has bad grommets and will distort badly. Parts Available: dust cover hinge, motor, platter, Top (dust cover). UNIT NEEDS STYLUS. #8 condition.
Stylus only, beryllium cantilever w/ shibata nude tip.m 1 available Low use #8+ condition
Contact us about similar items or replacement parts.
1 Drive motor board, with motor but motor itself has shorted coil, some work on drive circuit repaired (board works, parts value) - $28 (motor located in T-110) , 1 Transformer, model# 4002022 - $16, 1 Main power & control board with pitch controls and AC switch, S-0015 CMK-77X - Call to break specific parts, 1 Light bezel, All condition #9
(1) MMI-6S2PRI with pulley ($28) (1) Motor for Linear arm with pulley ($24) Low use tested & clean #9 condition
Local customers, please do not come to the shop without calling ahead first - (617) 926-8020 - for an appointment, so that we can more efficiently help you with your equipment or sound recording needs.
Matsushita MMN-6P2RK 8 VDC motor with brass pulley , mounted on circuit board # SUP 15700A / TP-N88S from low use working unit #9 condition.
Speed Shift Lever - 1 unit available Please Read Carefully! This is the rarest demanded lever Total 2 and 1/2 " long - threaded end is 1/4". Lever itself has 2 cuts to allow fit into speed pitch dial. Paddle is 1 and 1/2 inch long and paddle width is 1/2". 1 available with slight wear #8 condition
Parts unit - Call for Price and parts. Available parts include : Dust cover - no cracks but typical swirls and scratches and can be polished out #7 condition. Platter Matte, Platter, Motor, Counter weight # 9 condition No Headshell. Please call for price and availability.
#431 10132, Possible 3V - 9V DC Motor, For Use on Turntables (Technics), Clockwise Motor, Needs Outboard Regulator, With Plastic Pulley, Tested OK, Condition #9
Bang & Olufsen counter weight for RX -series. ( 1 and 17/16" l x 10/16 Dia , center shaft hole 3/16" ). Arm shaft still attached to counter weight but broken at attachment point - For replacing Counter Weight Only . Used - pulled from damaged unit. #9 Condition.
We leave "SOLD" items on our website for machines that we often repair and provide parts for. This is to give you an idea of the products we typically carry, and direct you to alternatives you may not know about - we often have substitutes for out-of-stock parts, and are happy to recommend workarounds and different solutions to common problems.
Type (#5773) Many parts available. Unit in good working condition. Dust cover (SOLD) Counter Weight ($14) Platter ($20) Motor ($60) Cartridge MMC-4 (Call) Cartridge suspension is bottomed out. Belt removed. #8 + good condition. Dust cover is excellent!
Speed selector mechanism for 33/45 . Includes steel rod and cage to guide lever as well as the screw . Also has the start stop switch. No tear drop handle included (check our other listings) Good condition #9 pulled from a damaged unit
United Audio logo badge. Walnut veneer base w/ press board bottom. (16 10/16" W X 14 6/16" D X 3 1/2" H) Has slot (Full length) on rear for dust cover. 16" long 1/4" wide. Good condition left front foot broken (easy repair) few H2O stains on front left bottom edge w/ chip. Can easily be refinished. Chip i svery minor 1/2" chip. #8 condition.
(5) available, priced individually. Machined aluminum. Heavy weight. Shows some wear. Condition #8
Parts available Motor, Platter, Platter matte, Counter Weight, Main Belt, Dust Cover. NOTE: No headshell carrier, No pitch belt.
Turntable motor with pulley, mount plate & wiring harness. 12 Volt. Serviced from turntable w/ broken tone arm. Good Condition #9
Contact us about similar items or replacement parts.
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
used good condition, with IC#8340630 Pulled from turntable w/ broken arm. Condition #9. (2) Available Priced Each
Dust cover with hinges complete. Cover does have some scuffs, maybe able to buff off. Good condition no cracks or broken corners. Value mostly for the hinges. #7 condition
Contact us about similar items or replacement parts.
Use for a single 33 play record. This spindle is a short spindle with rubber stop collar. Custom made with spacer grommet. Works like original. Fits BIC 920,940,960,980 1000 models 3 Available Excellent condition #9+ condition - $12/ea
4 Speed, 60Hz Brass pulley For use on 5mm axel Pulley shows some wear but good - condition #8
EG-530SD-3F, 5/12 vDC, 1130/1520/2360/1405 RPM, regulator on board, wire harness w/ switches (bushings+mount screws) , often substitutes for many of these motors, tested condition 9.
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
9.9 Shaft, 81 Grams counterweight, condition #9
Counterweight substitute. Looks very similar. Condition #9.