For Garrard TT in KLH M20 (mad by Garrard) . Part #3D 110-125V 12W, 0-15A 60AC. Note: no Pulley must use own pulley. Used, #9 condition (known low use)
(good hinge springs) (28$)#9 condition, Platter and Mat (28$) #8 condition, Many parts available. Unit is mostly complete ( start lever is bent but usable)#9 overall condition
Counter Weight. Fits Pioneer series OL-5xxx (PL-15r) 1.25 long 32mm. ID shaft diameter 7/16" 12mm. Outside diameter 1 3/16". Silver with black scale. #9 condition.
Black weight at bottom of aluminum counter weight. Imbedded in aluminium shaft offset hole DIA 8mm for arm. Overall size: L= 22mm, Dia= 33mm. Black Wt Dia = 2/mm. #8 condition, used. Has some scuffs and nicks but very usable.
Turntable broken arm. Platter (#9 condition), Motor (#9 condition), Pitch control (#9 condition). Back hinge slot for 1/2 by 1/2 inch stem fit dust cover. Hinges , no feet, see other listing. #7 condition,
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Motor complete with pulley switch board, speedgear pulley, springs, no belt. Serviced , oiled tested. #9 condition.
45 Adaptor spindle - Aluminum - approx. 1 -10/16th in diameter. We think that this is for the Thorens TD 160. (It will not fit the TD 145 correctly- seats too high off the platter surface) Good condition #9
For Parts unit was known to be working but damaged cosmetics. (1) Arm lock , (1) Motor board with NEC D554C function IC.($54) (1) bottom base. (2) 2902, JRC special servo or operation IC. (1) Display board ($24). (2) controls. (4) feet calibration spring (no rubber feet), Call for more info 617-926-8020.
6 volt CW, from virtually unused turn table , tested oil. #9
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
DC-12 v, Brass Pulley for TT ( 0.75" Length). 6 mt. holes 1/2" C-C ( Motor-housing Ht, 1 6/16" DM 1 9/16 wide) 5 terminal board @base. Known low use, tested #8+
Contact us about similar items or replacement parts.
1 - Motor MHN-3P2RDB $68, 1 - Motor speed board 49 2267030 $24 (with all parts wires intact has I.C. 1003C2 for speed control), Tested and oiled, known low modest use items. #8+ condition
Full size linear tracking turntable. ( problem with computer to run operation, is a possible problem) Available motors OK (see listing # 70168). Platter #9 condition(20$), Mat #9 condition(20$), Cover #8 condition (20$), Hinges ($20 the pair), Main circuit board guaranteed working #SUPB40-2(A)($24) . Call for other parts. #8
Typical small weight, silver dial. (1 1/4" x 9/16"). #9 condition.
1 1/2" L x 11/10" diameter, fits type 5712 5773 ( Rx2 + RX2) Ultra low mass arms, tapered silver front, black barreled body. Good #9 condition.
1/2 inch shaft dia hole, 1 inch long 0 to 2.5 gram scale. #9 condition.
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Platter and Mat, LE 505-507 Series, may fit others, Call for more Dual parts, Condition 9+
#SFDPD2NO1A, Same as many Technics, Spindle cycle gear is cracked, repairable on request, Unit has special AN6639 motor IC, Condition #8 - $28 - Call for availability
Possible Elac or miracord,. Nickle finish with 12 black lines, 1 1/4 inch diameter. 1 inch long. #8 condition.
0-5 gram scale, 1 1/8 long, 1 3/8 diameter. #9 condition.
0 to 2.5 gram scale, 5/8 inner shelf hole, 1 inch long with a chrome look. #9 condition
We are a very different kind of shop. To help ensure a smoother experience please read our letter about our current shop policies.
Outer ring of platter, For models TD-125, TD-145, TD-165, TD-150, Has usual stains around rim, easy to buff out, Condition 8+
Slot insert hinges used in many modern inexpensive turntables. Read description carefully. 1 1/2" by 7/8" plate fits into cover. 1 3/8" long by 11/16" wide fits into slot of turntable base 'T' slot. Black (all plastic).