(1) Power transformer B-6698, $24, (1) Counter mech, $14, (1) Clear bezel (over meters), $8, Silver buttons (specify which button needed) $4 ea. (1) Face (no scratches, minor ding at corner but nice #8) $18 (1) Faders $12 (1) Microprocessor B-6367A $16 (1) Faders (PCB w/controls) $8
Vintage Cassette Recorder, Silver Face Panel, Large VU meters, 3 position bias / EQ Switches (Normal, CrO2, Fe, Cr) Mic Input L&R, Headphone out, dolby B, Limiter on/off, Keyed controls are tight, Heads are 80% good, Capstan roller glazed, but will clean up. #8 condition (parts unit)
Contact us about similar items or replacement parts.
For BX Series, possibly BX-100, BX-150 etc., Condition #9
CCW rotation, 12v, Oiled and tested, Condition #9
Contact us about similar items or replacement parts.
Local customers, please do not come to the shop without calling ahead first - (617) 926-8020 - for an appointment, so that we can more efficiently help you with your equipment or sound recording needs.
Covers counter controls, switches. call for parts. #8 condition.
Idler tire, used in BX series, CR series. O.D = 0.590, C/S = 0.0787, Wall = 0.0985. (1) available NEW.
Was N.O.S., but little lock tabs at under front broken off, 3-491-205, Condition #8
Machine for parts, Good drive idler #9, Motor for capstan #9, Good heads #9, Good pinch roller #9, other Good boards & motors etc #9 cosmetic parts / knobs (no eject button) Call directly 617-926-8020 for orders.
W/ Brass pulley, 220uf/16v rubicon cap soldered to terminal board, (Matsushita motor MMI-5B9LA) used good condition, salvage unit #9
We are presently operating on an APPOINTMENT ONLY basis. Please call us first at (617) 926-8020 to schedule an appointment before you come into the shop for repairs, rentals, product recommendations, consultations, or anything other than minor purchases.
DC 12 V. USED - Good Condition, Salvaged Unit. #8+
Contact us about similar items or replacement parts.
Motor, max 11 VDC, W/ Brass "Gripper" Pulley + Mounting Plate. USED- Good Condition. #9
(2) Available, Brass Pully, Appears REV/FF. For nakamichi, use with 20.0mm C-C. Mounting holes 7/8" Note: pully may need to come off of shaft cut for nakamichi. #9 * substitute for Mabuchi RF-500T
(1) Black face plate #8 has minor but obvious scratch on face at meter window , few almost invisible dings at edges, lettering perfect (16$). (1) Door Cover (Sold), (1) Transport parts (call), (1) Heads 80% good (24$), Play head sold Nakamichi heads can appear to look worn but this design has a high "crown" which give the look of wide wear path. (1) Forward Pinch roller #9 (16$), (1) Back Pinch roller and guide #9 ($22), (1) Idler, Rubber, Arm #8(18$), (1) Back tension drag belt ($4), (1) Motor board #9 ($34), (1) Idler motor BHS7B02 #8-interchangeable with Sankyo BFs9B03 ($44), (1) Head Azimuth gear assembly #9 ($24). Table hubs available, Door frame available, also many other parts IC, Faders, Knobs (call),
Hinges intact, Needs TLC, Obvious wear but intact, Condition #7
Idler tire, STC. 5629 for BX & CR Models (2 available)
We are a very different kind of shop. To help ensure a smoother experience please read our letter about our current shop policies.
Top Quality Machine, 3 head design, front panel bias, headphone level. Calibrated for speed & Maxell Tape, head alignment and belts perfect, total clean all mechanics. Circuit board ruggedized at lll important solder locations, regulators, connectors. #9- condition.
Contact us about similar items or replacement parts.
With 2 stage Pulley for belts. Oiled tested known low use. #8 condition. SEE LISTING 60625 FOR REPLACEMENT.
Contact us about similar items or replacement parts.
Erase head T3710 complete kit with shims + hardware (8$), Play Rec Head complete compete with screws/mts + wire harness, Head condition good - buff before sale can be made #9 condition (24$), Supply Hubs- complete with springs brake pad + Lock washer (8$), Take Up Hubs - complete with springs, brake pads, lock washer, (8$). Pinch Roller #9, needs to be cleaned (12$).
# BFA2L36 with brass pulley. Used in BX series, with mounts & screws. Oiled & tested. Used pulled from salvage unit. Used for years but test ok. #8 (POSSIBLY SOLD)
4 13/16" X 3 2/16" Cassette Door, has 1 1/4 inch scratch on lower right hand corner- runs towards top. but very usable ! #7- Good condition
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Single deck, silver face, left/right VU meters *motor #MMX-6H2LSA and #MMN-6A7W *Needs belt. Excellent #7 condition, virtually no use time.
Head #9 Condition (nearly unworn) $48, Pinch roller,Supply and take-up Condition #9 $28/ea., Counter $20, Head mech alignment, gears, tape guide etc., other mechanical parts, Call -