(1) BF A2L36 Motor w/ Pulley, #8 Condition -(SOLD), (1) Par Tape Hubs with Springs and Little Washers - $14, (1) Function Motor VA700BOY with Switches, Gears - $40, Pinch Roller #8 Condition - $12 Unit has seen 20% of it wear life on all parts
#9 condition.
Head #9 Condition (nearly unworn) $48, Pinch roller,Supply and take-up Condition #9 $28/ea., Counter $20, Head mech alignment, gears, tape guide etc., other mechanical parts, Call -
Single deck, silver face, left/right VU meters *motor #MMX-6H2LSA and #MMN-6A7W *Needs belt. Excellent #7 condition, virtually no use time.
4 13/16" X 3 2/16" Cassette Door, has 1 1/4 inch scratch on lower right hand corner- runs towards top. but very usable ! #7- Good condition
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
# BFA2L36 with brass pulley. Used in BX series, with mounts & screws. Oiled & tested. Used pulled from salvage unit. Used for years but test ok. #8 (POSSIBLY SOLD)
Erase head T3710 complete kit with shims + hardware (8$), Play Rec Head complete compete with screws/mts + wire harness, Head condition good - buff before sale can be made #9 condition (24$), Supply Hubs- complete with springs brake pad + Lock washer (8$), Take Up Hubs - complete with springs, brake pads, lock washer, (8$). Pinch Roller #9, needs to be cleaned (12$).
With 2 stage Pulley for belts. Oiled tested known low use. #8 condition. SEE LISTING 60625 FOR REPLACEMENT.
Contact us about similar items or replacement parts.
Top Quality Machine, 3 head design, front panel bias, headphone level. Calibrated for speed & Maxell Tape, head alignment and belts perfect, total clean all mechanics. Circuit board ruggedized at lll important solder locations, regulators, connectors. #9- condition.
Contact us about similar items or replacement parts.
Idler tire, STC. 5629 for BX & CR Models (2 available)
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Hinges intact, Needs TLC, Obvious wear but intact, Condition #7
(1) Black face plate #8 has minor but obvious scratch on face at meter window , few almost invisible dings at edges, lettering perfect (16$). (1) Door Cover (Sold), (1) Transport parts (call), (1) Heads 80% good (24$), Play head sold Nakamichi heads can appear to look worn but this design has a high "crown" which give the look of wide wear path. (1) Forward Pinch roller #9 (16$), (1) Back Pinch roller and guide #9 ($22), (1) Idler, Rubber, Arm #8(18$), (1) Back tension drag belt ($4), (1) Motor board #9 ($34), (1) Idler motor BHS7B02 #8-interchangeable with Sankyo BFs9B03 ($44), (1) Head Azimuth gear assembly #9 ($24). Table hubs available, Door frame available, also many other parts IC, Faders, Knobs (call),
(2) Available, Brass Pully, Appears REV/FF. For nakamichi, use with 20.0mm C-C. Mounting holes 7/8" Note: pully may need to come off of shaft cut for nakamichi. #9 * substitute for Mabuchi RF-500T
Motor, max 11 VDC, W/ Brass "Gripper" Pulley + Mounting Plate. USED- Good Condition. #9
DC 12 V. USED - Good Condition, Salvaged Unit. #8+
Contact us about similar items or replacement parts.
W/ Brass pulley, 220uf/16v rubicon cap soldered to terminal board, (Matsushita motor MMI-5B9LA) used good condition, salvage unit #9
Customers outside of the US, please note that international shipping can be costly (US Post $16 minimum - up to 8oz or 226g). We are glad to combine orders to reduce shipping costs. Take a look at our shipping policies for more information and estimates of prices and shipping time.
Machine for parts, Good drive idler #9, Motor for capstan #9, Good heads #9, Good pinch roller #9, other Good boards & motors etc #9 cosmetic parts / knobs (no eject button) Call directly 617-926-8020 for orders.
Was N.O.S., but little lock tabs at under front broken off, 3-491-205, Condition #8
Idler tire, used in BX series, CR series. O.D = 0.590, C/S = 0.0787, Wall = 0.0985. (1) available NEW.
Covers counter controls, switches. call for parts. #8 condition.
CCW rotation, 12v, Oiled and tested, Condition #9
Contact us about similar items or replacement parts.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
For BX Series, possibly BX-100, BX-150 etc., Condition #9