Battery powered electronic cleaner. Used in good condition #8
with harness and connector block. Made in Germany. Excellent condition, tested.
Similar to AM-400. Excellent condition, tested.
Part #: 227 330 / 227 329 ; has original wire harness and original 60hz pulley. Salvage from low use machine, oiled and fully tested. Minor surface rust. Condition: 8
#431 10132, Possible 3V - 9V DC Motor, For Use on Turntables (Technics), Clockwise Motor, Needs Outboard Regulator, With Plastic Pulley, Tested OK, Condition #9
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Motor #MMN-656K8A with pulley. 9/10 condition low use and tested
MMX-3H2RPA Motor, DC12V. With Pulley. Fully tested, working, with board, connectors intact. Known low use, tested #9 condition.
Complete tone arm with cue elevator and counterweight assembly. With ant-skate side arm weight, no head shell. Arm wire from arm stem is 2" long. #9
Motor. Has original wiring harness and plastic connector housing. (No pulley). Round black motor housing with three mounting bolts. Shaft Diameter 0.058" Oiled, light use but good, #8+ Condition
Phono preamp with RIAA equalization. (This is a Mono Device) , Uses 8-pin socket connector. (1 only) Excellent #9 condition.
MM-6T2RWO Motor with switch and mounting screws. #9 Condition.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
9v DC motor, CCW rotation direction, with wire leads, board, and brass pulley. Matsushita MMI-6S9RWH. Excellent condition, tested good.
12v 2 speed pulley, very common version, fits many models. Remove jumper for speed control. From low use, tested. #9+ condition.
can go either CW or CCW depending on polarity of voltage, with brass pulley, tested and lubricated, salvaged #8 condition.
4 speed, 60Hz. Excellent condition. No Pulley.
Smoked dust cover. Hinge pin holes are 12 1/2" space. Truly excellent, very minor scuffs at edge. condition #9-
We leave "SOLD" items on our website for machines that we often repair and provide parts for. This is to give you an idea of the products we typically carry, and direct you to alternatives you may not know about - we often have substitutes for out-of-stock parts, and are happy to recommend workarounds and different solutions to common problems.
complete w/ wire leads, round motor axl size pulley, tested, oiled, condition # 8+
6 volt CW, from virtually unused turn table , tested oil. #9
with 4mm axle #9 condition low use tested oiled.
(2) available, priced individually. Clone stylus. PM4027D. Conical stylus. Tracking force 3.0-5.0 grams. NEW. Condition 10.
24 pole 300 rpm with pulley and wires. #9 condition (known no use time)
motor, #20-47 1001 same as #18-008-05, has 4 pin Molex connector, tested, condition #9
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
Dust cover and hinges. Complete top and bottom. Smokey tint color. Typical light scuffing & wear on cover. #8+
12VDC turntable motor, for Technics QT22D210. #9 used in excellent condition.