(1) MMI-6S2PRI with pulley ($28) (1) Motor for Linear arm with pulley ($24) Low use tested & clean #9 condition
1 Drive motor board, with motor but motor itself has shorted coil, some work on drive circuit repaired (board works, parts value) - $28 (motor located in T-110) , 1 Transformer, model# 4002022 - $16, 1 Main power & control board with pitch controls and AC switch, S-0015 CMK-77X - Call to break specific parts, 1 Light bezel, All condition #9
Stylus only, beryllium cantilever w/ shibata nude tip.m 1 available Low use #8+ condition
Contact us about similar items or replacement parts.
Unit is functional but cartridge mmc-5 has bad grommets and will distort badly. Parts Available: dust cover hinge, motor, platter, Top (dust cover). UNIT NEEDS STYLUS. #8 condition.
Counter weight . Black with silver numbers and scale. Very good condition #9
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Slot insert hinges used in many modern inexpensive turntables. Read description carefully. 1 1/2" by 7/8" plate fits into cover. 1 3/8" long by 11/16" wide fits into slot of turntable base 'T' slot. Black (all plastic).
Outer ring of platter, For models TD-125, TD-145, TD-165, TD-150, Has usual stains around rim, easy to buff out, Condition 8+
0 to 2.5 gram scale, 5/8 inner shelf hole, 1 inch long with a chrome look. #9 condition
0-5 gram scale, 1 1/8 long, 1 3/8 diameter. #9 condition.
Possible Elac or miracord,. Nickle finish with 12 black lines, 1 1/4 inch diameter. 1 inch long. #8 condition.
We leave "SOLD" items on our website for machines that we often repair and provide parts for. This is to give you an idea of the products we typically carry, and direct you to alternatives you may not know about - we often have substitutes for out-of-stock parts, and are happy to recommend workarounds and different solutions to common problems.
#SFDPD2NO1A, Same as many Technics, Spindle cycle gear is cracked, repairable on request, Unit has special AN6639 motor IC, Condition #8 - $28 - Call for availability
Platter and Mat, LE 505-507 Series, may fit others, Call for more Dual parts, Condition 9+
1/2 inch shaft dia hole, 1 inch long 0 to 2.5 gram scale. #9 condition.
1 1/2" L x 11/10" diameter, fits type 5712 5773 ( Rx2 + RX2) Ultra low mass arms, tapered silver front, black barreled body. Good #9 condition.
Typical small weight, silver dial. (1 1/4" x 9/16"). #9 condition.
Full size linear tracking turntable. ( problem with computer to run operation, is a possible problem) Available motors OK (see listing # 70168). Platter #9 condition(20$), Mat #9 condition(20$), Cover #8 condition (20$), Hinges ($20 the pair), Main circuit board guaranteed working #SUPB40-2(A)($24) . Call for other parts. #8
Customers outside of the US, please note that international shipping can be costly (US Post $16 minimum - up to 8oz or 226g). We are glad to combine orders to reduce shipping costs. Take a look at our shipping policies for more information and estimates of prices and shipping time.
1 - Motor MHN-3P2RDB $68, 1 - Motor speed board 49 2267030 $24 (with all parts wires intact has I.C. 1003C2 for speed control), Tested and oiled, known low modest use items. #8+ condition
DC-12 v, Brass Pulley for TT ( 0.75" Length). 6 mt. holes 1/2" C-C ( Motor-housing Ht, 1 6/16" DM 1 9/16 wide) 5 terminal board @base. Known low use, tested #8+
Contact us about similar items or replacement parts.
6 volt CW, from virtually unused turn table , tested oil. #9
For Parts unit was known to be working but damaged cosmetics. (1) Arm lock , (1) Motor board with NEC D554C function IC.($54) (1) bottom base. (2) 2902, JRC special servo or operation IC. (1) Display board ($24). (2) controls. (4) feet calibration spring (no rubber feet), Call for more info 617-926-8020.
45 Adaptor spindle - Aluminum - approx. 1 -10/16th in diameter. We think that this is for the Thorens TD 160. (It will not fit the TD 145 correctly- seats too high off the platter surface) Good condition #9
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Motor complete with pulley switch board, speedgear pulley, springs, no belt. Serviced , oiled tested. #9 condition.