possibly for SX680, SX750, SX630? Board is tested and working, but sold as is, in need of some capacitor replacements.
For many models, 1 NEC FIP# FIP7B8AS ($28), 1 CMOS IC# LC7258 ($28), Tested - From salvage, Condition #9
(possibly for SX 828, 949), 6 ct. - lever switch knobs, 4 ct. - function/selection knobs, 2 ct. - concentric (right/left) knobs, 1 ct. - tuning knob with 2 set screws, due to slight age look - can be cleaned up, #8+ condition
We leave "SOLD" items on our website for machines that we often repair and provide parts for. This is to give you an idea of the products we typically carry, and direct you to alternatives you may not know about - we often have substitutes for out-of-stock parts, and are happy to recommend workarounds and different solutions to common problems.
Intact, good condition parts machine. This unit has noisy transistors, preamp and amp circuit, and other problems but is fully intact and in good condition for hobbyists. Wooden case in good #7 condition with some obvious wear at edges. Will break down for knobs, boards, switches, cosmetic parts, etc, or sell as a complete unit.
Wooden top cover, 8 condition, Minor scuff on top (Sold). Bottom panel, 8+ condition, minor scratches $28. Top cover metal, found another 8+ condition SOLD
Power switch. Special high current 6A/96A250V. 10 condition (new).
Board #AWG060-0. Front panel switch board for muting, volume, balance, loudness, mode, adapter, and tape functions. (from right to left). Two rotary switches with appropriate nuts and washers. 9/10 condition, fully functioning and good condition, pulled from used machine.
Silver face plate with big oversized handles nicely mounted at edge of face sides. No knobs or switches included. Previous owner installed key lock power switch in left corner, nicely done, special key is with unit, 8+/10 condition, very minor scratches near volume and balance controls. Lexan dial face and glass cleaned thoroughly, JPG 135444 Condition #8+
Contact us about similar items or replacement parts.
Board #157BIXK. Power supply board. 8+/10 condition
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Board #AWX1260TXL. 9/10 condition, salvaged and tested.
Board #AW3-0. Rectifier board. 8/10 condition, relay may need cleaning.
Board# AWE092AKXL. Tuning board module. Varicon tuning gear will be required to reset (in comparison to another Varicon another board is the best way to compare). 8/10 condition.
Contact us about similar items or replacement parts.
Board #GWM105-0. Mic input jack module. 9/10 condition (pulled from used machine, in good shape and working condition).
Board# AWF0310. Phono preamp. 9/10 condition, salvaged and tested.
Board# AWM121-0. Push switch board for speaker selection with headphone 1/4 inch output jack. 9/10 condition, pulled from used machine, in good shape and working condition.
We have been selling and repairing professional and consumer audio equipment for over 40 years. (Read some of our customers testimonials here).
Amp board and heat sink module. Board #AWH07401XLC. 8+/10 condition, pulled from used machine, good shape and in working condition.
Contact us about similar items or replacement parts.
Push switch for input selection. Automatic spring loaded recoil when changing input selection. Board #GWS133-0. 9/10 condition, pulled from used machine, in good shape and in working condition.
Board #AWG0590. Front panel switch board for treble 20/10KHZ, tone, bass 100/50KHZ (from right to left). Four rotary switches with appropriate nuts and washers. 8+/10 condition, fully functioning and good condition, pulled from used machine.
Phono1 cartridge load control module with rotary switch. Board #GWS 134-0. 8/10 condition, fully functioning and obvious use.
Front panel FM/AM tuner dial. 8 watt, signal and tuning meters can be sold separately if need be. Meters $24 each. 9/10 in great cosmetic condition.
Push switch board for FM and filter functions. Board#AWM119-0. 9/10 condition, fully functioning and in good shape, pulled from used machine.
We are presently operating on an APPOINTMENT ONLY basis. Please call us first at (617) 926-8020 to schedule an appointment before you come into the shop for repairs, rentals, product recommendations, consultations, or anything other than minor purchases.
Each knob $14. Complete knob set for silver face plate. No Tuning Knob Each knob properly labeled and organized into individual and respective bags. 9/10 condition, cosmetically in very good condition.
Back panel with all input and output jacks with AM wand. 9/10 condition, complete assembly, can sell individual parts if need be- CALL. Very good cosmetic condition.