Pro DJ Mixer, 3ch + mic, 3x phono 6x line, fx loop, 3 band eq per channel, x-fader reverse, Hi mid low kills on ch 1 & 3, High Quality Faders and Knobs
Contact us about similar items or replacement parts.
2 Channels, soft start (no noise on/off), 2 phone/line inputs, 3 band EQ per channel, mic input with tone control, cue master/meter switching. W/original box/package. *Left channel mid control does not work*, otherwise good condition, cosmetics look good, works well. #7 condition
Folio FX8 with manual and Power supply, Lexicon FX processor with 16 presets.
Mixing console with manual and heavy duty road case. Unit has excellent cosmetics. 23 Mixing Channels (1 channel needed for parts), 8 channel bus. Thoroughly cleaned, calibrated, and serviced (smooth faders, clean pots, upgraded power supply, etc). Channel 1 has been robbed for a few controls otherwise the machine has been restored to excellent condition with many OP Amps, wires, and grounds replaced. The unit has seen very little use time because it had an early failure of cracked soldering at the bus board connectors. In fact we have resoldered all bus board connectors at all bus board connectors at this point. As well, replaced many op amps to reduce the noise floor and improve RF sepression.
In deed, in this era, certain 5532 Op Amps were worse or better depending upon their actual use in the circuit. Specifically, Texas Instrument 5532s provided a better noise floor than the original Signetics type. This is a rare case were certain Op Amp types can make a significant difference. Cosmetics and mechanics of the board are in 90 point condition. Improvements on the power supply , capacitors, etc have been done. In all honestly, normally these boards are known to age badly but this unit has not seen any serious use time so it cleaned up well. My only reservation is the gain control pots on the mic pres on these English designs like Allen Heath, TAC Scorpion, Hill, and Soundcraft as well as many others of this design type had slightly noisy gain trims due to DC off set in the Mic/Preamp gain stage. This is a common problem with all of them and easy to work around. In fact, some engineers do not even notice. This boards have the English sound, somewhat warm and a little soft in the dynamic range due to mostly passive circuit parts in the filters for equalization.
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Simple, compact, portable mixer with 4 mic/line ins (48v power) and two sets of stereo inputs. Excellent #9 condition, professionally cleaned/serviced/tested with minor updates to improve grounding. Very quiet operation.
14 channels, channel 1-10 xlr and 1/4" in, channel 11-14 1/4" for stereo or mono in, 6 aux outs 1/4", direct in for each channel 1/4", 4 stereo returns with individual controls 1/4", 2 stereo fx 1/4" each own levels, R+L Led Meter, 4 band EQ for each track and trim, GRPS, Mix, Phones, Power supply Rack mountable
Contact us about similar items or replacement parts.
As is, passes signal but needs service. Connectors, controls, and switches appear to need cleaning. Power supply works. No power supply, $20 -- or with power supply, $48.
Top Quality Design with individual channel cards for ease of service. Sweep EQ Midrange, Quality Mic Pre. Mint condition All channel All controls check OK. Virtually no use time ! #9 condition
Contact us about similar items or replacement parts.
Marked "RUWIDO" on side, "10K + 1g" on bottom. New, unused. Five available. *At this point the best I have offered to many people is a very similar fader, usually Japanaese with correct length fit hole to hole mount, but 10k or 20k fader value will work virtually the same. Many faders are pulled from wrecked consoles but faders can be cleaned, tightened or sometimes are like new. I will not sell worn faders. Average cost is $8-$14 for basic faders, $14-$22 for these special glass carbon epoxy types. Please show a picture that clearly shows hole to hole length.
Contact us about similar items or replacement parts.
For Soundcraft and others, manufactured by O Meg. 10k, Lin A. New
Customers outside of the US, please note that international shipping can be costly (US Post $16 minimum - up to 8oz or 226g). We are glad to combine orders to reduce shipping costs. Take a look at our shipping policies for more information and estimates of prices and shipping time.
Log scale pots for Soundcraft and possibly other British consoles, Trident, Tangent, etc. Made in UK by 0meg. New old stock. Six pieces available.
We know you have many options for purchasing audio equipment and parts, and we truly appreciate your business. We strive to offer good products at competitive prices. While we can't always match the prices of one isolated reseller, we make up for it by carefully selecting, testing, and finding unique and special rare parts, and we are here for the long run. We guarantee everything we sell and we hope it helps you to enjoy a great listening experience.
For Soundcraft and others. 10k with switch. O Meg 4A.2S. new.
For parts or as-is. 8 channel mixing console. Unit in excellent mechanical and cosmetic condition. Has defective CX770 IC or noisy preamp IC, which could be fixed with correct install of parts. Great condition, #9
with brace case
Contact us about similar items or replacement parts.
Need your guitar or bass amp tuned up? We are now doing repairs, upgrades, and modifications to all types of guitar amps. Orange, Mesa Boogie, Fender, Marshall, Hughes and Kettner, Peavey, Ampeg, Gibson, Silvertone, etc. Read more about it here
Audio Mixer (consumer audio), 4 inputs, 1/4 phone(front), all rear connectors RCA
Contact us about similar items or replacement parts.
Powered Mixer, 12 ch, 250watt 4ohm per side, dual 7 band, built in DSP.
Contact us about similar items or replacement parts.